Ilman. alv: 39,83 €
Kiertohimmennin, joka käynnistyy 1 W:n kuormituksella!
Vadsbo Transformersin erittäin tehokas transistorihimmennin VD100 on suunniteltu erityisesti LED-lampuille ja LED-liitäntälaitteille. Se toimii hyvin myös 230 V:n hehkulamppujen, halogeenien ja elektronisten muuntajien kanssa.
Himmennin käynnistyy jo 1 W:n kuormituksella ja kestää jopa 100 W:n kuormia. VD 100:ssa on sisäänrakennettu suojaus ylikuormitusta, ylikuumenemista (115 °C:n automaattinen nollaus) ja transientteja vastaan.
Himmentimessä on porrastoiminto ja takareunaohjaus.
Himmennin asennetaan kojerasiaan, ja se sopii ulkonäöltään Elkon RS -sarjan tuotteisiin.
Pakkaus sisältää myös ylimääräisen kehyksen/painikkeen, jolla himmennin on yhteensopiva Schneiderin Exxact-sarjan kanssa.
| Teho | 100 W |
|---|---|
| Teho (lowest) | 1 W |
| Kotelointiluokka | IP20 |
| Jännite | 230 V |
| Leveys | 84 mm |
|---|---|
| Korkeus | 84 mm |
| Syvyys | 45 mm |
| Mitat | L83xK83xS47 mm |
| Leveys | 9 cm |
|---|---|
| Korkeus | 13 cm |
| Syvyys | 6 cm |
| Paino | 122 g |
Right knowledge and precautions are important when working with electricity. Most electrical work must be performed by a qualified electrician, however you can carry out some basic work yourself, if you have knowledge of how to do this. As the owner or occupant of a property, you are responsible that the electricity is installed properly and that the electrical appliances you use are in full working order and used correctly.
If you are unsure, you should leave the job to a qualified electrician. Incorrect use of electricity can result in fire and injury/damage. Never take a chance, a single mistake can have fatal consequences.
Irrespective of the type of electrical work that you're doing, you should always start by turning off the power. Remove the plug if it is an appliance you intend to work on. If the electrical work concerns parts of the fixed installation such as ceiling luminaires, wall sockets or switches, you should remove the fuses or turn off the main circuit breaker.
Check that the power really is off and that the equipment you intend to work on is de-energised before you start. Also, make sure that nobody can turn the power on while you are working.
If the fuse blows again there is a fault that must be rectified. Contact an electrician if you are not able to find the error. Blown fuses must be discarded - never try to repair them.
Make sure that the new light source does not have more power than that indicated on the luminaire, for example: “Max. 10 W”. Also exercise care to follow other instructions set out on the luminaire. It is especially important when it comes to the use of top reflector bulbs and halogen lamps.
If you put together an extension cord to be used in an earthed power outlet, all parts of the extension cord must be in earthed design. Do not forget to check the green-yellow protective conductor to ensure it is secured correctly in the right place. It may never be connected to any other terminal screw than those with an earth symbol.
If the cord is broken or if the insulation is damaged, do not fix it. However, you can cut off the broken part. You may only replace the cord, plugs and connectors with the same kind of material as before. (If you need to change the plug on a lamp with one of a different kind or on appliances, they should be left with an expert for conversion.)
Be careful. Disconnect the power either by unscrewing the fuse or by turning off the main circuit breaker. Make sure there is no voltage in the switch or socket before you start to work.
What you may do yourself in these areas in a home, provided that you have knowledge concerning this, is to replace a permanently connected luminaire or to permanently connect a luminaire where power lines have been routed. Otherwise, you need to contact a qualified electrician.
Perustuu 361 arvioon
Kaikki arvostelut on kirjoitettu asiakkailta, jotka ovat ostaneet Julalta ja noudattaa meidän arvostelukäytäntöä. Lue lisää arvostelukäytännöstämme.
